I used my soldering skills to solder primary ide port to internal cf connector that was desoldered from webdt board. I used #28 wirewrap wires. I used black tape to isolate each pins from each other and the board. I have 2 silicon power cf cards, one with xp and the other with puppy linux. I just pop in the cf card I want to boot from. Everything is self contained. I know that I have no more cf card slot to ti cardbus but I really do not need it.
Search for "CTAN007-TrueIDE pdf" for pin connections.
my ide to cf mod
Re: my ide to cf mod
Nice Work!With the tiny DOM gone you can have any OS,cool!
I had never been inspired to try what you did.It never occured to me.
cgrape2
I had never been inspired to try what you did.It never occured to me.
cgrape2
-
- Full Member
- Posts: 112
- Joined: Fri Apr 24, 2009 5:20 pm
- Location: Sussex, New Brunswick, CAN
Re: my ide to cf mod
I have found this http://www.cactus-tech.com/download/CTAN007-TrueIDE-20080603.pdf document. If this is the one you refer to it shows "a sample schematic of how to connect the pins from a CF Card socket to a 40 pin ATA connector on a typical host motherboard so that the CF Card can be used in TrueIDE mode". The DT366 has a 44 pin connector. Did you wire the DT366 up as per the 40 pin drawing? If I did not get the proper document could you kindly post the one you used?mylise wrote: Search for "CTAN007-TrueIDE pdf" for pin connections.
Have you actually tested this setup and found it working?
Bruce
Last edited by plane_crazy on Sat Jan 16, 2010 12:19 pm, edited 1 time in total.
plane_crazy
-
- Full Member
- Posts: 112
- Joined: Fri Apr 24, 2009 5:20 pm
- Location: Sussex, New Brunswick, CAN
Re: my ide to cf mod
Yes, that is the right document, Bruce
Sorry ... the last 4 pins are
41 +3.3VDC 42 +3.3VDC
43 GND 44 Type (0==ATA)
Connect pins 41 and 42 together to where VCC is identified on pcmcia_cf connector.
Pin 43 is connect to gnd
Pin 44 is NOT connected anywhere
Please note that CF connector has all pins in a row on the motherboard. You must be careful with the assignments
1 26 2 27 3 28 ... 24 49 25 50
For the primary IDE you have
2 4 6 ... 42 44
1 3 5 ... 41 43
Use the following jumper settings seen in the document
Master ... short 1,2
DMA support ... short 7,8
DMA support ... short 9,10
NOTE: I did not use an IDC header but directly connected these wires together!
for additional pictures,click http://imgur.com/TVwVb.jpg
Sorry ... the last 4 pins are
41 +3.3VDC 42 +3.3VDC
43 GND 44 Type (0==ATA)
Connect pins 41 and 42 together to where VCC is identified on pcmcia_cf connector.
Pin 43 is connect to gnd
Pin 44 is NOT connected anywhere
Please note that CF connector has all pins in a row on the motherboard. You must be careful with the assignments
1 26 2 27 3 28 ... 24 49 25 50
For the primary IDE you have
2 4 6 ... 42 44
1 3 5 ... 41 43
Use the following jumper settings seen in the document
Master ... short 1,2
DMA support ... short 7,8
DMA support ... short 9,10
NOTE: I did not use an IDC header but directly connected these wires together!
for additional pictures,click http://imgur.com/TVwVb.jpg
Last edited by mylise on Mon Jan 25, 2010 9:29 pm, edited 1 time in total.
-
- Administrator
- Posts: 569
- Joined: Tue Mar 24, 2009 9:11 pm
Re: my ide to cf mod
Sorry for the limits on pictures. I ask that you link to external galleries. Over the past two years I have been out of work twice due to injury, relocated three times and generally cant afford much in the form of bandwidth. I wont allow advertisements here out of principle and often disappear of the map for a month or so at a time when I do go out of work or relocate. As I cant maintain the site like I want to external links make sense.
By the way congrats on your mod! Nice job.
quotaholic
By the way congrats on your mod! Nice job.
quotaholic
Re: my ide to cf mod
I wonder if somebody els make this mod. and post if it is working oke and some pictures from the mod.
I own a dt366 and i use it for Homeseer HStouch as a touchpanel for my homecontol.
The problem with CE5.0 is it supports no transparency.
With tinyxp the problem i get is the program Hstouch.exe for windows crasht.
So if this mod. is working fine, i can get a full windows xp version running.
Thanks in advance
John
I own a dt366 and i use it for Homeseer HStouch as a touchpanel for my homecontol.
The problem with CE5.0 is it supports no transparency.
With tinyxp the problem i get is the program Hstouch.exe for windows crasht.
So if this mod. is working fine, i can get a full windows xp version running.
Thanks in advance
John